สืบค้นงานวิจัย
การออกแบบระบบบำบัดน้ำเสียจากโรงงานฟอกย้อมสิ่งทอโดยวิธีตะกอนเร่งแบบกึ่งต่อเนื่อง
วิชุดา นิมิตรไชยาพงศ์ - มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าธนบุรี
ชื่อเรื่อง: การออกแบบระบบบำบัดน้ำเสียจากโรงงานฟอกย้อมสิ่งทอโดยวิธีตะกอนเร่งแบบกึ่งต่อเนื่อง
ผู้แต่ง / หัวหน้าโครงการ: วิชุดา นิมิตรไชยาพงศ์
บทคัดย่อ (EN): This research was done to study the design of wastewater treatment system fordyeing factory by using Cyclic Activated Sludge System (CASS). The study was concerned withthe cycle treatment of combined wastewater fiom production line and dormitory wastewater formaximum efficiency and lowest cost.Since the BOD5/COD ratio of wastewater is 0.37, therefor it could be treated bybiological treatment and reaction rate constant was 0.08, ultimate load BOD was 474.78 mg/lwere used to calculate the CASS system. From CASS design, the BOD load of water treatmentsystem was 0.15 kg/m3 , flow rate was 3,000 m3 /d , F/M Ratio was 0.06 and volume of CASS was6,000 m3 . The result wastewater analysis showed that the nutrients were sufficient due to theinfluent fiom dormitory wastewater.From the result of study the optimum aeration time, it was found that the treatmentwith the fill-aerated time, fill- settle time and decanting time of 6: 4: 2 by hours and flow ratewas 3,000 m3/d gives the highest efficiency with dissolved oxygen in the range of 0.26-2.67mg/l and lowest electrical cost. It was able to reduce BOD, COD, TKN and PO43- 98.56%,78.00%, 95.44% and 81.05% respectively and the electrical consumption is lower than the other two systems.
บทคัดย่อ: ไม่พบข้อมูลจากหน่วยงานต้นทาง
ภาษา (EN): th
เอกสารแนบ: http://dcms.thailis.or.th/dcms/dccheck.php?Int_code=54&RecId=6037&obj_id=17499
เผยแพร่โดย: มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าธนบุรี
คำสำคัญ (EN): Cyclic Activated Sludge System (@ASS)
เจ้าของลิขสิทธิ์: มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าธนบุรี
รายละเอียด: This research was done to study the design of wastewater treatment system fordyeing factory by using Cyclic Activated Sludge System (CASS). The study was concerned withthe cycle treatment of combined wastewater fiom production line and dormitory wastewater formaximum efficiency and lowest cost.Since the BOD5/COD ratio of wastewater is 0.37, therefor it could be treated bybiological treatment and reaction rate constant was 0.08, ultimate load BOD was 474.78 mg/lwere used to calculate the CASS system. From CASS design, the BOD load of water treatmentsystem was 0.15 kg/m3 , flow rate was 3,000 m3 /d , F/M Ratio was 0.06 and volume of CASS was6,000 m3 . The result wastewater analysis showed that the nutrients were sufficient due to theinfluent fiom dormitory wastewater.From the result of study the optimum aeration time, it was found that the treatmentwith the fill-aerated time, fill- settle time and decanting time of 6: 4: 2 by hours and flow ratewas 3,000 m3/d gives the highest efficiency with dissolved oxygen in the range of 0.26-2.67mg/l and lowest electrical cost. It was able to reduce BOD, COD, TKN and PO43- 98.56%,78.00%, 95.44% and 81.05% respectively and the electrical consumption is lower than the other two systems.
หากไม่พบเอกสารฉบับเต็ม (Full Text) โปรดติดต่อหน่วยงานเจ้าของข้อมูล

การอ้างอิง


TARR Wordcloud:
การออกแบบระบบบำบัดน้ำเสียจากโรงงานฟอกย้อมสิ่งทอโดยวิธีตะกอนเร่งแบบกึ่งต่อเนื่อง
มหาวิทยาลัยเทคโนโลยีพระจอมเกล้าธนบุรี
2543
การใช้ประโยชน์จากกากตะกอนน้ำเสียโรงงานฟอกย้อมในการผลิตปุ๋ย การศึกษาการกำจัดสีย้อมสิ่งทอโดยสารส้มและผงเมล็ดมะขามโดยกระบวนการสร้างและรวมตะกอน การกำจัดสีและของแข็งแขวนลอยทั้งหมดในน้ำเสียจากโรงงานสิ่งทอด้วยตะกอนสารส้มร่วมกับพ การกำจัดสีย้อมประเภทสีดิสเพอร์สจากน้ำเสียจากการฟอกย้อมสิ่งทอด้วยระบบถ่านกัมมันต์ชนิดเกล็ด-เอสบีอาร์ การออกแบบหนังสืออิเล็กทรอนิกส์เพื่อเรียนรู้การออกแบบเชิงนิเวศเศรษฐกิจของผู้ผลิตผ้าฝ้ายทอมือย้อมสีธรรมชาติ การบำบัดสีในน้ำสีรีแอกทีฟจากโรงงานฟอกย้อมโดยกระบวนการไฟฟ้าเคมี ระบบการกำจัดกลิ่นจากระบบบำบัดน้ำเสียโดยวิธีการกรองแบบชีวภาพ การศึกษาวิธีที่เหมาะสมในการตรวจสอบ หมู่เบนซิดีนในสีที่มีหมู่อะโซต้องห้าม สำหรับผลิตภัณฑ์สิ่งทอ อัตลักษณ์หญิงทอผ้า : กรณีศึกษาผู้หญิงทอผ้าในโรงงานแห่งหนึ่งที่นครหลวงเวียงจันทน์ สปป. ลาว วิธีการออกแบบและขยายขนาดเครื่องอบแห้งแบบพ่นฝอยโดยใช้เครื่องต้นแบบ
คัดลอก URL
กระทู้ของฉัน
ผลการสืบค้นทั้งหมด โพสต์     เรียงลำดับจาก